Full Size 3-Way High-Directivity Line Array With Compression Suspension System


Full Size 3-Way High-Directivity Line Array With Compression ASM Suspension System

  • New 4th Generation HF Waveguide technology
  • Revolutionary D2 Dual Diaphragm, Dual Voice Coil Compression Driver
  • JBL’s patented RBI (Radiation Boundary Integrator®)
  • Cardioid-Arrayable Subwoofer Enclosure Models
  • Aluminum front baffles for reduced cabinet height, weight and improved heat transfer
  • Brand new V25 compression suspension system
  • Accessories optimized for vertical transportation and deployment
  • V5 Processing with Crown I-Tech HD or VRACK
  • JBL HiQnet Performance Manager™ System Configuration and Control
  • Available with either fixed angle tension suspension (V25-II) or compression suspension (V25-II-CS) hardware


The revolutionary D2 Dual Driver dramatically improves the sound and performance of high frequencies, providing an extreme output advantage over conventional systems with significantly higher array power, reduced distortion, double the number of voice coils and more than double the power handling. This results in a dramatic increase in pure high frequency sound pressure levels in the same physical footprint with a 30% reduction in weight.

Improved Wavefront Control
The V25‐II waveguide provides better acoustic loading conditions for the D2 driver, resulting in 10 dB higher sensitivity above 10 kHz.

Enhanced Performance and Dramatically Reduced Driver Weight
JBL's exclusive dual voice coil, dual magnetic gap Differential Drive technology is at the core of all VTX models, dramatically reducing driver weight while greatly enhancing all critical performance parameters: frequency response, power output and distortion.

Precision Pattern Control
Precise VTX V25 vertical pattern control requires precise focus for optimum audience coverage and the VTX-LZ laser accessory provides a cost-effective installation tool to help streamline the setup process.

System Integration and Management

With the VTX Series you are not just using a product, you are gaining access to an expert system. Tools for system design and all the components to analyze, configure, set up and control a VTX system are all part of the JBL commitment to total system integration and support. The goal is maximum efficiency and the highest possible level of performance in any venue, anywhere in the world.

Training and Support
In addition to designing the most sophisticated sound reinforcement system available, JBL Professional provides the expertise to achieve the maximum performance possible. Our 65+ years of expertise in the use of systems in venues around the world is an invaluable resource that is at the core of our training curriculum, helping you to maximize both the use and your investment in the VTX System.

Visit www.jblpro.com/training for latest training dates and registration.
System Type Full Size 3-Way High Directivity Line Array Element with D2 Dual Drivers
Components 2 x 2267H 15" Differential Drive® LF
4 x 2169H 8" Differential Drive® MF
3 x 2430K D2 Dual Driver
Horizontal Coverage (-6 dB) 90 degrees nominal (300 - 16k Hz)
Frequency Range (-10 dB) 35 - 18k Hz
Nominal Section Impedances 2 x 8 ohms LF, 8 ohms MF, 8 ohms HF
Continuous Power Rating 2 x 2000W LF, 1400W MF, 600W HF
Dimensions (W x H x D) 1223 mm x 414 mm x 614 mm
(48.2" x 16.3" x 24.2")
Weight 82.6 kg (182 lb)

VTX V25 AF | Array Frame

Array Frame used for suspending or ground stacking VTX V25 series enclosures. The VTX-V25-AF is also compatible with the VTX S28 dual 18” subwoofer enclosures. Includes height-adjustable leveling feet for ground stack applications. Optional VTX-V25-AF-EB extension bar available.

  • Compatible with VTX V25, VTX V25-CS, VTX V25-II, VTX V25-II-CS and VTX S28
  • 9 pick points available for single point suspension
  • Optional Extension Bar available
  • Flexible front-to-back or side-by-side pick point options
  • Supports up to 24 cabinets (array geometry dependent)
  • Can be used for ground stack applications
  • Pick point shackle size: 5/8” or 3/4”
  • 1 x VTX-V25-AF
  • 4 x height-adjustable leveling feet for ground stack applications
  • 4 x Quick Release Pins (QRP) for securing top enclosure to the frame
VTX V25 AF EB | Array Frame

Extension Bar accessory used in conjunction with the VTX-V25-AF array frame for deploying VTX V25 series systems in either compression or tension mode. Five extension bar attachment options provide variable pick point separation (2-point suspension) and added flexibility for single point suspension. The extension bar can be front- or rear-mounted for increased array up-tilt or down-tilt, respectively. When rear-mounted, provides an attachment point for compression suspension. A single extension bar can be installed in the array frame central tube, or alternatively, a pair of extension bars can be front or rear-mounted in left/right array frame tubes. Single or dual extension bars can also be front- or rear-mounted in ground stack applications for extra stability and a wider range of array tilt angle options. Dual extension bars can also be front-and rear-mounted for compression suspension when increased array up-tilt is required.
  • Compatible with VTX-V25-AF
  • 2 x pick points available for single point suspension
  • 1 x pick point available for VTX-V25-LH level hoist attachment
  • Supports up to 24 cabinets (array geometry dependent)
  • Pick point shackle size: 5/8” or 3/4”
  • 1 x VTX-V25-AF-EB extension bar
  • 1 x height-adjustable leveling foot for ground stack applications
  • 2 x Quick Release Pins (QRP) for securing the extension bar to the array frame
VTX V25 PB | Pull Back Accessory

Pull Back accessory for attachment to the bottom V25 enclosure to facilitate compression suspension of VTX V25-II-CS or VTX V25-CS arrays. Compression can be implemented using a separate chain motor and suspension point (Rear Motor Pullback) or by using an optional VTX-V25-LH lever hoist or chain motor attached to the VTX-V25-AF-EB extension bar (Extension Bar Pullback). The VTX-V25-PB is also compatible with non Compression Suspension V25 enclosures and can be used for rear motor pullback configurations.
  • Compatible with VTX V25-II, VTX V25-II-CS, VTX V25, VTX V25-CS
  • Can be used with VTX-V25-LH lever hoist or separate pull back suspension point
  • Supports up to 2000 lbs of pull back force
  • Shackle size: 5/8” (included)
  • 1 x central pullback bar with 2x left/right adapter brackets for connection to bottom V25 cabinet
  • 2 x 5/8” shackles for attaching spreader bar to chain bridle
  • 1 x 24” dual leg chain bridle with locking safety hooks and upper master link for attachment to compression or pullback device

VTX V25 LH | Lever Hoist

Factory-approved manual lever hoist for compression of VTX V25-II-CS systems. The CM Series 653 for use with VTX V25- II-CS is a 1.5 ton model with 6 meters (20’) of chain length for compressing arrays of up to 24x VTX V25-II-CS or V25-CS cabinets (array geometry dependent) with no additional extension hardware needed.
  • CM Series 653
  • 1.5 ton model
  • 6 meters (20’) of chain length
  • Support for up to 24 x VTX-V25-II-CS Cabinets (array geometry dependent)
  • 1 x Columbus McKinnon (CM) Lever Hoist (1.5 ton rating) with 6 meters (20’) of chain


Designed to facilitate fast attachment and precise alignment of VTX V20 and V25-II / V25-II-CS systems, the VTX V20-DF is a lightweight solution for providing wider coverage at the bottom of VTX V25-II / V25-II-CS arrays. Lightweight design with multiple options for angle between V25-II / V25-II-CS and V20 (3.5deg, 7.5deg, 11deg). Able to be used as a down-fill adapter frame for V25-II arrays, or as a downfill adapter frame + pullback frame for compression of VTX V25-II-CS arrays with V20 downfill. Supports up to 6x VTX V20 cabinets suspended underneath VTX V25-II / V25-II-CS.
  • Angle options: 3.5deg, 7.5deg, 11deg
  • Lightweight design
  • Precise HF exit alignment between V25-II and V20
  • Support for up to 6x VTX V20 cabinets


The VTX-V25-VTC vertical transporter is a simple and cost-effective solution for vertically transporting VTX V25-II-CS and VTX-V25-CS enclosures in blocks of 3 or 4 cabinets high. Measuring 48.1” wide by 25” deep, the VTX-V25-VTC will travel 4 across (length-wise) in standard 100” trucks. Reinforced protective covers (VTX-V25-VT-CVR) supplied separately.
  • Vertical transporter for 3x or 4x V25 enclosures
  • Compatible with VTX V25-II-CS and VTX V25-CS
  • Heavy duty locking casters
  • Stackable for easy storage
  • Dimensioned for efficient truck pack
  • Lightweight, rugged construction
  • 1 x VTX-V25-VTC


Reinforced, padded protective cover for 3x or 4x VTX-V25-II-CS enclosures when transported vertically.
  • Handle cutouts, heavy-duty zippers
  • Modular design, can be used with 3x or 4x VTX V25-II-CS enclosures
  • Rear panel access flaps for input connectors
  • Speaker cabinets can be tested without fully removing the cover
  • Lightweight, durable construction
  • 1 x VTX-V25-VT-CVR

VTX LZ PS | Power Supply

Rechargeable power supply unit (ships with US 120V plug only) for powering VTX-LZ laser units. The VTX-LZ-PS includes a male (out) 3-Pin XLR connector for easy connectivity with VTX-LZ laser units using standard microphone cables. The VTXLZ-PZ can power up to 10x VTX-LZ lasers by using the IN/OUT XLR connectors on the laser units. The power supply unit casing is made out of a rugged, road ready composite material and is water resistant. The typical battery life for VTX-LZPS powering a single VTX-LZ is 15-hours and about 3-hours when powering 10x VTX-LZ in parallel.
  • Power supply unit for powering VTX-LZ units
  • Rechargeable battery included
  • Includes AC adapter (120V US plug only)
  • Standard 3-Pin XLR connectors for easy wiring to VTX-LZ laser units using standard mic cables
  • Able to power up to 10x VTX-LZ units
  • 1 x VTX-LZ-PS power supply
  • 1 x AC adapter with 120V US plug

VTX LZ | Laser

The VTX-LZ laser unit has been designed to securely attach to VTX or VERTEC line array systems using cabinet specific Mount Bracket (MB) accessories (supplied separately). When energized using the VTX-LZ-PS power supply unit, VTX-LZ generates a flashing bright green ray of light on-axis with the center of the loudspeaker enclosure that it is attached. This provides an accurate site angle reference for system installation or measurement microphone placement for system tuning. Green lasers are significantly brighter than red lasers, allowing the VTX-LZ laser to be used over long distances indoors or outdoors. The VTX-LZ includes IN and OUT (Female / Male) 3-Pin XLR connector for easy connectivity with multiple VTX-LZ laser units using standard microphone cables. Up to 10x VTX-LZ lasers can be used with 1x VTX-LZ-PS by using the IN/OUT XLR connectors.
  • Class 3R green laser for use with VTX or VERTEC Systems
  • 3-Pin XLR IN and OUT connectors for power supply connectivity and for powering multiple VTX-LZ units
  • Up to 10x VTX-LZ can be powered by 1 x VTX-PS
  • Mount brackets available for VTX and VERTEC systems (sold separately)
  • Fan-cooled for extended laser lifetime
  • Class 3R green laser for use with VTX or VERTEC Systems

VTX LZ V25 MB | Mount Bracket

The VTX-LZ-V25-MB mount bracket has been designed to securely attach VTX-LZ units to VTX V25, VTX V25-II or VTX V25-II-CS line array systems. When properly mounted on a VTX line array system, the VTX-LZ laser provides a visual reference to confirm on-axis vertical site angle aiming (focus) of the array. Coverage simulations based on JBL Line Array Calculator II software (LAC-II) indicate the desired location where the laser should aim and the VTX-LZ laser provides visual confirmation to assist with actual installation in the field. The VTX-LZ-V25-MB can be attached to either the left or right side of a V25 enclosure.
  • Mount Bracket to attach VTX-LZ to VTX V25
  • Compatible with VTX V25, V25-II and V25-II-CS
  • VTX-LZ and VTX-LZ-PS sold separately
  • 1 x VTX-LZ-V25-MB
  • 1 x Quick Release Pin with lanyard